Ice-O-Matic GEM0650A/W Instrukcja Użytkownika Strona 1

ICE-O-Matic11100 East 45th AveDenver, Colorado 80239Part Number 9081350-01 Date 2/07 SERVICE AND INSTALLATION MANUALGEM0650A/W,GEM0956A/W and GEM1256

GEM0650/0956/1256 A/W For the Installer Page 4 Bin Application The GEM Series are designed to fit the following ICE-O-Matic Bins. ●B42, using Bin

GEM0650/0956/1256 A/W For the Installer Page 5 Location: ICE-O-Matic ice machines are designed to be installed indoors in a controlled environmen

GEM 0650/0956/1256 A/W For the Installer Page 6 Allow 6 “Clearance for Air Circulation A proper installation locates t

GEM0650/0956/1256 A/W For the Plumber Page 7 Water Inlet: ●Air Cooled Models: The recommended water supply is clean, cold water. Use 3/8 inch O.

GEM0650/0956/1256 A/W For the Electrician Page 8 Electrical Connections: Check the ice machine nameplate (located on the back panel) for the volt

GEM0650/0956/1256A/W For the Installer Page 9 Final Check List: _______1. Is the ice machine installed indoors in a location where the air and

GEM0650/0956/1256 A/W Start Up Page 10 Pre-Start Inspection: 1. Remove the front and side service panels. 2. Check that any shipping blocks hav

GEM0650/0956/1256 A/W Component Description Page 11 ●Control Box: Contains the electrical controls that operate the machine. ●High Pressure Cut O

GEM0650/0956/1256 A/W Component Description Page 12 ●Contactor: A definite purpose contactor connecting the compressor and the fan motor to the

GEM0650/0956/1256 A/W Component Description Page 13 ●Evaporator: A refrigerated vertical tube filled with water and containing a water seal and

GEM0650/0956/1256 A/W Electrical Sequence Page 14 Electrical Sequence: There are 7 indicator lights on the control board: ●WTR-OK: (Water OK) G

GEM0650/0956/1256 A/W Operation: Water Page 15 Water enters the machine through the 3/8 inch male flare at the rear of the cabinet, goes to the w

GEM0650/0956/1256 A/W Operation: Performance Page 16 Beginning at the compressor, the refrigerant is compressed into a high temperature gas. The

GEM0650/0956/1256 A/W Sanitizing and Cleaning Page 17 It is the USER’S RESPONSIBILITY to keep the ice machine and ice storage bin in a sanitary c

GEM0650/0956/1256 A/W Bearing Maintenance Page Bearing Maintenance: The bearing in the breaker should also be checked at least two (2) times per

GEM0650/0956/1256 A/W Sensor Maintenance Page 19 Slide Bin Controls to Remove Bin Control Sensor: The bin control uses devices that sense light,

GEM0650/0956/1256 A/W Maintenance: Air Cooled 20 Clean the air cooled condenser: Air flow on this model is from front to back, so the inside of

GEM0650/0956/1256 A/W Auger Maintenance Page 21 Auger: In some areas, the water supply to the ice machine will contain a high concentration of mi

GEM0650/0956/1256 A/W Service Diagnosis Page 22 Symptom Possible Cause Probable Correction No ice is made nothing operates. •Unit off due

GEM0650/0956/1256 A/W Service Diagnosis Page 23 Symptom Possible Cause Probable Correction Unit makes ice, but very slowly •High dischar

GEM0650/0956/1256 A/W Forward Page i How To Use This Manual ICE-O-Matic provides this manual as an aid to the end user and service technician in

GEM0650/0956/1256 A/W Control System Diagnostics Page 24 The Control System consists of: ●Control Board ●Water Sensors ●Ice Sensors ●High Pressur

GEM0650/0956/1256 A/W R&R- Water Reservoir, Bin Control Page 25 Water Reservoir: 1. Disconnect electrical power supply. 2. Shut off water

GEM0650/0956/1256 A/W R&R-Bearing and Breaker Page 26 Note: Removal of the auger, water seal, evaporator and gear motor must begin at the top

GEM0650/0956/1256 A/W R&R-Auger Page 27 To Remove the Auger: 1. Disconnect electrical power. 2. Turn off the water to the machine. 3. Unclip

GEM0650/0956/1256 A/W R&R-Water Seal Page To Remove the Water Seal: (Assuming all steps to remove the auger have been performed) 1. The gear

GEM0650/0956/1256 A/W R&R-Evaporator Page 29 To Replace the Evaporator: (Assuming all steps for removal of the thrust bearing, breaker, auge

GEM0650/0956/1256 A/W R&R-Gear Motor Page 30 To Check the Gear Motor: 1. Remove wires from terminals 1 and 2 2. Use an ohmeter to check for

GEM0650/0956/1256 A/W R&R-Fan Blade and Motor Page 31 To Remove the Condenser Fan Motor Assembly: (GEM0956 Shown) 1. Disconnect electrical po

GEM0650/0956/1256 A/W Refrigeration System Service Page 32 Refrigeration Service: General: This ice machine uses R404A refrigerant and polyoles

GEM0650/0956/1256 A/W GEM0650 Wiring Diagram Page 33 Wiring Diagram GEM0650 A/W

GEM0650/0956/1256 A/W Table Of Contents Page ii Table of Contents Forward...

GEM0650/0956/1256 A/W GEM0956 Wiring Diagram Page 34 Wiring Diagram GEM0956 A/W

GEM0650/0956/1256 A/W GEM1256 Wiring Diagram Page 35 Wiring Diagram GEM1256 A/W

GEM0650/0956/1256 A/W GEM0655 Wiring Diagram Page 36 Wiring Diagram GEM0655 Air

GEM0650/0956/1256 A/W Service History Page 37 What to Do Before Calling for Service: ●Check the water supply to the ice machine. The ice machin

GEM0650/0956/1256 A/W Freight Claim Procedure Page iii Important! Inspect Promptly This merchandise has been carefully inspected and packed in ac

GEM0650/0956/1256 A/W Warranty Page iv ICE-O-Matic Parts and Labor Domestic & International Limited Warranty Mile High Equipment LLC (the “

GEM0650/0956/1256 A/W For the Installer Page 1 Installation Guidelines: For proper operation of the ICE-O-Matic ice machine, the following instal

GEM0650/0956/1256 A/W For The Installer Page 2 GEM0650/0655/0956A/W

GEM0650/0956/1256 A/W For The Installer Page 3 GEM1256A/W